熱塑性材料替代中壓設備中環氧絕緣體的可行性研究
戴永正1，劉永高1，顧宇鋒1，張明祖2
（1 江蘇南瑞泰事達電氣有限公司, 江蘇 泰州 225300；2 蘇州大學 材料與化學化工學部, 江蘇 蘇州 215123）
摘 要：基于對開關設備所用材料環保、回收再利用的要求，分析了環氧樹脂在使用中不環保及性能方面的缺陷，確定采用環保熱塑性工程塑料作為新材料替代熱固性環氧樹脂。通過分析PA、PC、PPO等熱塑性工程塑料的力學、電性能及加工特性，篩選出新材料的基體樹脂，依據材料特性確定改性路徑，通過實驗分析所制備的不同改性材料樣片，研究出材料配方、改性工藝。試驗結果表明，新型環保熱塑性復合絕緣材料質量輕、強度高、無毒無害阻燃且可回收再利用，滿足中壓開關設備對絕緣材料性能的要求。
關鍵詞：開關設備；熱塑性絕緣材料；環保；聚酰胺；環氧樹脂；改性
中圖分類號：TM643 文獻標識碼：A 文章編號：1007-3175(2018)04-0059-06
Investigation of Thermoplastic Composite Material Replacing Epoxy Insulator in Medium Voltage Switchgear
DAI Yong-zheng1, LIU Yong-gao1, GU Yu-feng1, ZHANG Ming-zu2
（1 Jiangsu Nari Turbostar Electric Co., Ltd, Taizhou 225300, China;
2 College of Chemistry, Chemical Engineering and Materials Science, Soochow University, Suzhou 215123, China）
Abstract: Based on the requirements of environmental protection and recycling of the material used for switching equipment, this paper analyzed the non environmental protection and the performance defects during the use of epoxy resin and determined that the environmental thermoplastic engineering plastics were used to replace the thermosetting epoxy resin. After mechanical, electrical and machining properties of these engineering thermoplastics, such as PA, PC and PPO were analyzed, this paper selected the suitable matrix resin of material, confirmed the modified path according to the material properties, carried out experimental analysis of preparative different modified material samples, and got the material formulation and modification process of this project. The test results show that the novel environmental protection thermoplastic composite insulation material is light in quality, high in strength, non-poisonous, unharmful, anti-flaming with reclcying and reusing, which meets the requirements of insulating material property for the medium voltage switchgear.
Key words: switchgear; thermoplastic insulation material; environmental protection; polyamide; epoxy resin; modification
參考文獻
[1] 付杰輝，陳曉東，徐群杰，等. 聚苯醚/ 聚酰胺合金的增容及增韌改性研究[J]. 塑料工業，2014，42(10)：36-39.
[2] 麥堪成，張聲春，高慶福，等. 聚苯硫醚/ 尼龍6共混物的結晶與熔融行為[J]. 高分子材料科學與工程，2000，16(3)：148-150.
[3] 管亦武，苑會林，錢丹，等. 聚苯醚/ 尼龍6共混體系相容性的研究[J]. 塑料工業，2008，36(9)：9-12.
[4] 張志軍，王全兵，劉愛學，等.PPS/SEBS-g-MAH/PA46合金的制備及性能研究[J]. 塑料工業，2012，40(11)：24-27.
[5] 彭蛟. 中壓固體絕緣技術的發展[J]. 電氣時代，2012(5)：76-77.
[6] 張偉，別群梅，袁錦瑤. 高CTI值、無鹵阻燃玻纖增強尼龍66的研究及應用[J]. 工程塑料應用，2006，34(8)：50-53.
[7] 彭治漢，施祖培. 塑料工業手冊——聚酰胺[M]. 北京：化學工業出版社，2001.
